README.md

    uNabto ESP32 cam demo

    Using Nabto's SDK, the smartConfig network function has been added. Thanks to Nabto's technical support, I solved the problem of network delay.

    This project turns the ESP32-CAM into a remote P2P accesible surveillance camera. It uses the esp-idf FreeRTOS based core (vs. some other demos which uses the arduino core). Also it uses the espressif esp32-cam library with slight modification (we could not get the reset to work).

    The video is MJPEG and the module can cope to remotely stream (encode to mjpeg and encrypt and integrity check) a VGA feed at around 10 frames per second.

    You should also read the related blog article: https://www.nabto.com/esp32/

    The structure

    The structure of the project is as follows

    
        +
        +-->+-------------+
        |   |    Main     |        This folder contains the initial setup
        |   +-------------+        and the application_event() function defining
        |                          the application
        +-->+-------------+
            |  Components |
            +-------------+
                          |
                          +------->+----------------+
                          |        | unabto         |    Don't edit here (link to other github rep)
                          |        +----------------+
                          |
                          +------->+----------------+
                          |        | unabto-esp-idf |    The platform integration
                          |        +----------------+
                          |
                          +------->+----------------+
                          |        | nabtotunnel    |    Nabto tunnel application
                          |        +----------------+
                          |
                          +------->+----------------+
                          |        | unabto-esp-    |    Client fingerprint database
                          |        | fingerprint    |    storage in NVS
                          |        +----------------+
                          |
                          +------->+----------------+
                                   | esp32-camera   |    From the espressif github (not a link, since we adjusted)
                                   +----------------+
    

    ESP-IDF project has a speciel structure. You can read more about that here: https://esp-idf.readthedocs.io/en/v1.0/build_system.html The unabto source and the integration code is done as components and therefore resides in the IDF component folder. The unabto sdk is a submodule link to the unabto generic source.

    The initial setup/commisioning and the application is located in the main folder. unabto_application.c contains the application (inside the application_event function), the main.c contains the setup and configuration of the WiFi module.

    How to set it up

    Step 1: Setup the ESP-IDF build environment

    Follow the setup of the ESP-IDF toolchain setup

    http://esp-idf.readthedocs.io/en/stable/get-started/index.html (WARNING!!! It is important to use the "stable" release not latests.. Issues with fcntl has been detected as of late june 2019)

    Step 2: Clone the repository

    git clone --recursive https://github.com/Ai-Thinker-Open/Ai-Thinker-Open_ESP32-CAMERA_WAN.git

    Step 3: Make menuconfig

    Enter into menu "Camera configuration"

    Edit/adjust the following menu items:

    • WIFI access point name (SSID) : The wifi access point you want the module to attach to
    • WIFI password : The password used by the access point
    • Nabto ID : The Nabto device id you get from your AppMyProduct account
    • Nabto key - 32 hex chars : The key for the specific device id you entered in the before mentioned item

    Camera wiring! If you have an ESP-EYE board nothing else needs to be set up if you have an “ESP32 Cam” from Ai Tinker you need to configure this too (also in the “Camera configuration” menu).

    Step 3: Build the project

    make

    Step 4: Flash the Image

    Possible you need to adjust the serial deivce to use for flashing which is setup in the menuconfig part, but mostly the standard setup will match your platform.

    make flash

    How to test the application

    Monitor the output from the board

    Using the monitor command you should see a printout similar to the following every time the ESP32-EVB starts up:

    Look for the "connected!" telling that the device knows how to connect to your WIFI. Also look for the Nabto state change to "ATTACHED" meaning that the device succesfully attached to Nabto infrastructure (registered and is online, waiting for connect requests from clients). The cloud service (controller) address can be varying dependent on geographic region (we have 4 datacenters) and availabillity.

    00:00:01:457 main.c(382) connected!
    00:00:01:460 main.c(388) IP Address:  192.168.2.147
    00:00:01:465 main.c(389) Subnet mask: 255.255.255.0
    00:00:01:470 main.c(390) Gateway:     192.168.2.1
    00:00:01:475 unabto_application.c(59) In demo_init
    00:00:01:479 unabto_application.c(78) Before fp_mem_init
    00:00:01:495 unabto_application.c(81) Before acl_ae_init
    00:00:01:495 unabto_common_main.c(110) Device id: 'jicnkjqs.ev9dbf.appmyproduct.com'
    00:00:01:498 unabto_common_main.c(111) Program Release 4.4.0-alpha.0
    00:00:01:505 network_adapter.c(140) Socket opened: port=5570
    00:00:01:510 network_adapter.c(140) Socket opened: port=49153
    00:00:01:515 unabto_stream_event.c(235) sizeof(stream__)=328
    00:00:01:521 unabto_context.c(55) SECURE ATTACH: 1, DATA: 1
    00:00:01:526 unabto_context.c(63) NONCE_SIZE: 32, CLEAR_TEXT: 0
    00:00:01:532 unabto_common_main.c(183) Nabto was successfully initialized
    00:00:01:539 unabto_context.c(55) SECURE ATTACH: 1, DATA: 1
    00:00:01:543 unabto_context.c(63) NONCE_SIZE: 32, CLEAR_TEXT: 0
    00:00:01:550 network_adapter.c(140) Socket opened: port=49154
    00:00:01:555 unabto_attach.c(770) State change from IDLE to WAIT_DNS
    00:00:01:561 unabto_attach.c(771) Resolving DNS for jicnkjqs.ev9dbf.appmyproduct.com
    00:00:01:675 unabto_attach.c(790) Resolved DNS for jicnkjqs.ev9dbf.appmyproduct.com to:
    00:00:01:675 unabto_attach.c(796)   Controller ip: 34.232.129.33
    00:00:01:678 unabto_attach.c(802) State change from WAIT_DNS to WAIT_BS
    00:00:01:887 unabto_attach.c(480) State change from WAIT_BS to WAIT_GSP
    00:00:01:888 unabto_attach.c(481) GSP address: 34.194.195.231:5565
    00:00:01:895 unabto_attach.c(270) ########    U_INVITE with LARGE nonce sent, version: - URL: -
    00:00:02:089 unabto_attach.c(563) State change from WAIT_GSP to ATTACHED

    To test the camera you can try to access: http://:8081/

    Which will show something like this:

    Download the AMP video app

    Download the Android or iPhone app from app store

    Pair the video app with the wifi module

    Setup your phone to be connected to the same WIFI network as the device. This is ultra important since the app and the device will do a broadcast discovery to find eachother. The app will create an anonomous PKI cert and send the fingerprint of the key (like SSH) to the device on the local network which is considered "safe" (ie. don't pair on public network). The device add this fingerprint to the access control list and after this the device will now accept that the app can remotely connect. Read more about Nabto access control lists and pairing here.

    Connect and view video

    Now you should be able to connect to the camera when you click on the camera logo.

    项目简介

    🚀 Github 镜像仓库 🚀

    源项目地址

    https://github.com/ai-thinker-open/ai-thinker-open_esp32-camera_wan

    发行版本

    当前项目没有发行版本

    贡献者 6

    A AI-Thinker-wm @AI-Thinker-wm
    C Carsten Gregersen @Carsten Gregersen
    D dezdeepblue @dezdeepblue
    N Nabto ApS @Nabto ApS

    开发语言

    • C 84.1 %
    • C++ 10.6 %
    • Objective-C 4.4 %
    • CMake 0.6 %
    • Makefile 0.3 %