This adds support for Radxa ROCK Pi E, rockchip rk3328 board.

Specification:

- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
    1 x 10/100/1000M Ethernet
    1 x 10/100M Ethernet
- Storage:
    1 x MicroSD Slot
    1 x eMMC Module Slot
- USB Host/OTG:
    1 x USB3.0 Type A HOST
    1 x USB2.0 HOST (40-pin pin-header)
- Wireless
    RTL8723DU/RTL8821CU
- Debug Serial:
    1500000 baud at UART2 ( 40-pin pin-header)
- Power Supply:
    Type-C 5V
    Optionally PoE

Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: NJayantajit Gogoi <jayanta.gogoi525@gmail.com>

Add uboot support for Radxa ROCK Pi E, rockchip rk3328 board.
Add pre-built files to fix swig dependencies.

Specification:

- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
    1 x 10/100/1000M Ethernet
    1 x 10/100M Ethernet
- USB Host:
    1 x USB3.0 Type A HOST
    1 x USB2.0 OTG (40-pin pin-header)
- Wireless:
    RTL8723DU/RTL8821CU
- Power Supply: Type-C 5V

Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: NJayantajit Gogoi <jayanta.gogoi525@gmail.com>

Will be used in upcoming hostapd changes
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

The bootcmd limits the kernel to 4 MiB which is
exceeded when using Device/FitImage. Device/FitzImage
reduces the size to around 3 MiB.
Reviewed-by: NRobert Marko <robimarko@gmail.com>
Signed-off-by: NThomas Bong <thomas.bong@devolo.de>

Renamed the interfaces to match the other devices.
Name the interface connected to the builtin G.hn chip 'ghn'.
This might toggle at runtime while the G.hn chip is in the
bootloader.
Reviewed-by: NRobert Marko <robimarko@gmail.com>
Signed-off-by: NThomas Bong <thomas.bong@devolo.de>

Update cmake to 3.27.4
No patch refresh needed.
Signed-off-by: NHannu Nyman <hannu.nyman@iki.fi>

Changes:
    9dc0800 wireless-regdb: Update regulatory rules for Philippines (PH)
    111ba89 wireless-regdb: Update regulatory rules for Egypt (EG) from March 2022 guidelines
    ae1421f wireless-regdb: Update regulatory info for Türkiye (TR)
    20e5b73 wireless-regdb: Update regulatory rules for Australia (AU) for June 2023
    991b1ef wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: NYuu Toriyama <PascalCoffeeLake@gmail.com>

Add reset-(de)assert-us to ethernet PHYs on Fortinet FortiGate 50E to
solve instability after HW resetting of PHYs. (ex.: restarting "network"
service, etc...)

Fixes: #13391
Fixes: 102dc5a6 ("mvebu: add support for Fortinet FortiGate 50E")
Signed-off-by: NINAGAKI Hiroshi <musashino.open@gmail.com>

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.51

No patches needed a rebased.  Update to checksum only.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: NJohn Audia <therealgraysky@proton.me>

Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.130

No patches needed a rebased. Update to checksum only.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: NJohn Audia <therealgraysky@proton.me>

When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Check for null instead of truish value
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

It returned the wrong value when using HT40-
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Fixes 40 MHz channel bandwidth on 2.4 GHz AP+STA
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Simplifies code and removes #ifdef statements
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.

It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.
Signed-off-by: NHank Moretti <mchank9999@gmail.com>

Remove stale sites from @GNOME alias:
* remove 2 sites that have stale 3 years old content
* remove 2 sites that have dropped GNOME
* convert 2 sites from FTP to HTTP
Signed-off-by: NHannu Nyman <hannu.nyman@iki.fi>

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.50

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod, ipq806x/R7800
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod, ipq806x/R7800
Signed-off-by: NJohn Audia <therealgraysky@proton.me>

Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.129

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: NJohn Audia <therealgraysky@proton.me>

When a dependency is pulled in via conditional depends, and the condition
is already selected earlier in the chain, drop the condition.
This avoids some corner cases that trigger recursive dependencies.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This reverts commit 6c3eff9d.
This appears to cause some regressions in generated config.
Will be replaced with a fixed version later
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This makes it easier to keep track of changes in the generated output,
when the script is modified
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

23a434d0d15d tests: fix expected test output
840ccdeeabce fw4: avoid emitting invalid rule jump targets
20da9933fd7e fw4: fix another instance of invalid rule jump targets
598d9fbb5179 fw4: remove special cases around hw flow offloading
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This allows supporting a mix of devices with or without hw offloading support
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

When a package foo depends on PACKAGE_foo:bar (in order to make build
dependencies conditional), tracking transitive dependencies can fail because
the internal seen flag is checked/set before eliminating the fake conditional
dependency. This can show up as a depends on not properly turned into a
select further down in the dependency chain
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Always enable nl80211 driver support
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This stops NVMEM driver from using MMIO access past booting and messing
with NAND controller state.

Link: https://forum.openwrt.org/t/asus-rt-ac88u-hw-a6-broken-in-22-03-3/147882Signed-off-by: NRafał Miłecki <rafal@milecki.pl>

1a07f1dff32b make_ethtool_modes_h.sh: apply anti-bashism
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>

f429bd94f99e system-linux: switch to new ETHTOOL_xLINKSETTINGS API

Fixes AN announcement for speeds beyond 1 GBit/s.
Adds new UCI options for Ethernet devices:
 - autoneg: switch on or off auto-negotiation
 - pause: if set to 0, do not announce symmetric flow control capability
 - asym_pause: if set to 0, do not announce asymmetric flow control
               capability.
 - rxpause: if set overrides AN and forces RX pause accordingly
 - txpause: if set overrides AN and forces TX pause accordingly
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>

Relocating the device tree is required for being apply to apply
device tree overylay at boot.

Fixes: 34bb3309 ("mediatek: use updated device tree overlay mechanism for BPi-R64")
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>

Without it, a lot of authentication modes fail without obvious error messages
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

It is no longer used
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

db3934d2f740 scripts/netifd-wireless.sh: properly fix WPA3 Enterprise support

Support the following values for the different WPA3 Enterprise modes:

- wpa3-mixed: WPA3 Enterprise transitional mode
	This supports EAP with both SHA1 and SHA-256, with optional MFP
- wpa3: WPA3 Enterprise only mode
	This supports only SHA256 with mandatory MFP
- wpa3-192: WPA3 Enterprise with mandatory 192 bit support
	This uses only GCMP-256 ciphers

Disable 192 bit support and GCMP-256 ciphers for the regular "wpa3" mode.
It seems that even leaving in optional 192 bit support breaks auth on some
clients, including iOS devices.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

WPA3 Enterprise-transitional requires optional MFP support and SHA1+SHA256
WPA3 Enterprise-only requires SHA1 support disabled and mandatory MFP.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Use the SHA384 variant to account for longer keys with more security
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This symbol was added by commit 2e6f34faa7e0 ("Input: Add IBM Operation
Panel driver") to v6.1. It depends on I2C so it's available to limited
amount of targets. It needs to be specified thought to allow kernel
configuration.

For bcm53xx this fixes:
IBM Operation Panel driver (INPUT_IBM_PANEL) [N/m/?] (NEW)
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NRafał Miłecki <rafal@milecki.pl>

It seems that this was not functioning properly and was likely completely unused.
Keeping this out of tree also introduced some annoying churn when updating, because
of the iw nl80211.h sync patch.
If this is needed, it will be reintroduced when/if it is added upstream
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

These suboptions (PLATFORM, FSL_MC and MLX5_VFIO_PCI)
may be prompted for when VFIO is enabled, regardless of
architecture.

These are not related to the main vfio use case
(passthrough of PCIe devices)
Signed-off-by: NMathew McBride <matt@traverse.com.au>

Arm platforms with the right hardware blocks (such as
GICv3.0+ interrupt controller and SMMU/IOMMU) are
able to use vfio-pci to pass through PCI devices
to a VM.
Signed-off-by: NMathew McBride <matt@traverse.com.au>