README 18.3 KB
Newer Older
1
        Linux kernel release 4.x <http://kernel.org/>
L
Linus Torvalds 已提交
2

3
These are the release notes for Linux version 4.  Read them carefully,
L
Linus Torvalds 已提交
4 5 6 7 8
as they tell you what this is all about, explain how to install the
kernel, and what to do if something goes wrong. 

WHAT IS LINUX?

X
Xose Vazquez Perez 已提交
9 10 11
  Linux is a clone of the operating system Unix, written from scratch by
  Linus Torvalds with assistance from a loosely-knit team of hackers across
  the Net. It aims towards POSIX and Single UNIX Specification compliance.
L
Linus Torvalds 已提交
12

X
Xose Vazquez Perez 已提交
13 14 15 16
  It has all the features you would expect in a modern fully-fledged Unix,
  including true multitasking, virtual memory, shared libraries, demand
  loading, shared copy-on-write executables, proper memory management,
  and multistack networking including IPv4 and IPv6.
L
Linus Torvalds 已提交
17 18 19 20 21 22

  It is distributed under the GNU General Public License - see the
  accompanying COPYING file for more details. 

ON WHAT HARDWARE DOES IT RUN?

X
Xose Vazquez Perez 已提交
23 24
  Although originally developed first for 32-bit x86-based PCs (386 or higher),
  today Linux also runs on (at least) the Compaq Alpha AXP, Sun SPARC and
25
  UltraSPARC, Motorola 68000, PowerPC, PowerPC64, ARM, Hitachi SuperH, Cell,
X
Xose Vazquez Perez 已提交
26
  IBM S/390, MIPS, HP PA-RISC, Intel IA-64, DEC VAX, AMD x86-64, AXIS CRIS,
T
Tracey Dent 已提交
27
  Xtensa, Tilera TILE, AVR32 and Renesas M32R architectures.
X
Xose Vazquez Perez 已提交
28 29 30 31 32 33

  Linux is easily portable to most general-purpose 32- or 64-bit architectures
  as long as they have a paged memory management unit (PMMU) and a port of the
  GNU C compiler (gcc) (part of The GNU Compiler Collection, GCC). Linux has
  also been ported to a number of architectures without a PMMU, although
  functionality is then obviously somewhat limited.
34 35
  Linux has also been ported to itself. You can now run the kernel as a
  userspace application - this is called UserMode Linux (UML).
L
Linus Torvalds 已提交
36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

DOCUMENTATION:

 - There is a lot of documentation available both in electronic form on
   the Internet and in books, both Linux-specific and pertaining to
   general UNIX questions.  I'd recommend looking into the documentation
   subdirectories on any Linux FTP site for the LDP (Linux Documentation
   Project) books.  This README is not meant to be documentation on the
   system: there are much better sources available.

 - There are various README files in the Documentation/ subdirectory:
   these typically contain kernel-specific installation notes for some 
   drivers for example. See Documentation/00-INDEX for a list of what
   is contained in each file.  Please read the Changes file, as it
   contains information about the problems, which may result by upgrading
   your kernel.

 - The Documentation/DocBook/ subdirectory contains several guides for
   kernel developers and users.  These guides can be rendered in a
R
Randy Dunlap 已提交
55 56 57
   number of formats:  PostScript (.ps), PDF, HTML, & man-pages, among others.
   After installation, "make psdocs", "make pdfdocs", "make htmldocs",
   or "make mandocs" will render the documentation in the requested format.
L
Linus Torvalds 已提交
58

R
Randy Dunlap 已提交
59
INSTALLING the kernel source:
L
Linus Torvalds 已提交
60 61 62 63 64

 - If you install the full sources, put the kernel tarball in a
   directory where you have permissions (eg. your home directory) and
   unpack it:

65
     gzip -cd linux-4.X.tar.gz | tar xvf -
L
Linus Torvalds 已提交
66

67 68
   or

69
     bzip2 -dc linux-4.X.tar.bz2 | tar xvf -
70

71
   Replace "X" with the version number of the latest kernel.
L
Linus Torvalds 已提交
72 73 74 75 76 77

   Do NOT use the /usr/src/linux area! This area has a (usually
   incomplete) set of kernel headers that are used by the library header
   files.  They should match the library, and not get messed up by
   whatever the kernel-du-jour happens to be.

78
 - You can also upgrade between 4.x releases by patching.  Patches are
H
Hkon Lvdal 已提交
79
   distributed in the traditional gzip and the newer bzip2 format.  To
L
Linus Torvalds 已提交
80
   install by patching, get all the newer patch files, enter the
81
   top level directory of the kernel source (linux-4.X) and execute:
L
Linus Torvalds 已提交
82

83
     gzip -cd ../patch-4.x.gz | patch -p1
L
Linus Torvalds 已提交
84 85

   or
86

87
     bzip2 -dc ../patch-4.x.bz2 | patch -p1
L
Linus Torvalds 已提交
88

89 90 91 92
   Replace "x" for all versions bigger than the version "X" of your current
   source tree, _in_order_, and you should be ok.  You may want to remove
   the backup files (some-file-name~ or some-file-name.orig), and make sure
   that there are no failed patches (some-file-name# or some-file-name.rej).
93
   If there are, either you or I have made a mistake.
L
Linus Torvalds 已提交
94

95
   Unlike patches for the 4.x kernels, patches for the 4.x.y kernels
96
   (also known as the -stable kernels) are not incremental but instead apply
97 98 99 100 101
   directly to the base 4.x kernel.  For example, if your base kernel is 4.0
   and you want to apply the 4.0.3 patch, you must not first apply the 4.0.1
   and 4.0.2 patches. Similarly, if you are running kernel version 4.0.2 and
   want to jump to 4.0.3, you must first reverse the 4.0.2 patch (that is,
   patch -R) _before_ applying the 4.0.3 patch. You can read more on this in
102
   Documentation/applying-patches.txt
103

L
Linus Torvalds 已提交
104 105 106 107
   Alternatively, the script patch-kernel can be used to automate this
   process.  It determines the current kernel version and applies any
   patches found.

M
Michael Witten 已提交
108
     linux/scripts/patch-kernel linux
L
Linus Torvalds 已提交
109 110 111 112 113 114 115

   The first argument in the command above is the location of the
   kernel source.  Patches are applied from the current directory, but
   an alternative directory can be specified as the second argument.

 - Make sure you have no stale .o files and dependencies lying around:

M
Michael Witten 已提交
116 117
     cd linux
     make mrproper
L
Linus Torvalds 已提交
118 119 120 121 122

   You should now have the sources correctly installed.

SOFTWARE REQUIREMENTS

123
   Compiling and running the 4.x kernels requires up-to-date
L
Linus Torvalds 已提交
124 125 126 127 128 129 130 131 132 133
   versions of various software packages.  Consult
   Documentation/Changes for the minimum version numbers required
   and how to get updates for these packages.  Beware that using
   excessively old versions of these packages can cause indirect
   errors that are very difficult to track down, so don't assume that
   you can just update packages when obvious problems arise during
   build or operation.

BUILD directory for the kernel:

M
Michael Witten 已提交
134
   When compiling the kernel, all output files will per default be
L
Linus Torvalds 已提交
135 136 137 138
   stored together with the kernel source code.
   Using the option "make O=output/dir" allow you to specify an alternate
   place for the output files (including .config).
   Example:
139

140
     kernel source code: /usr/src/linux-4.X
M
Michael Witten 已提交
141
     build directory:    /home/name/build/kernel
L
Linus Torvalds 已提交
142

M
Michael Witten 已提交
143
   To configure and build the kernel, use:
144

145
     cd /usr/src/linux-4.X
146 147 148
     make O=/home/name/build/kernel menuconfig
     make O=/home/name/build/kernel
     sudo make O=/home/name/build/kernel modules_install install
L
Linus Torvalds 已提交
149

M
Michael Witten 已提交
150
   Please note: If the 'O=output/dir' option is used, then it must be
L
Linus Torvalds 已提交
151 152 153 154 155 156 157 158 159 160 161
   used for all invocations of make.

CONFIGURING the kernel:

   Do not skip this step even if you are only upgrading one minor
   version.  New configuration options are added in each release, and
   odd problems will turn up if the configuration files are not set up
   as expected.  If you want to carry your existing configuration to a
   new version with minimal work, use "make oldconfig", which will
   only ask you for the answers to new questions.

162
 - Alternative configuration commands are:
163

M
Michael Witten 已提交
164
     "make config"      Plain text interface.
165

M
Michael Witten 已提交
166
     "make menuconfig"  Text based color menus, radiolists & dialogs.
167

M
Michael Witten 已提交
168
     "make nconfig"     Enhanced text based color menus.
169

M
Michael Witten 已提交
170
     "make xconfig"     X windows (Qt) based configuration tool.
171

M
Michael Witten 已提交
172
     "make gconfig"     X windows (Gtk) based configuration tool.
173

M
Michael Witten 已提交
174 175 176
     "make oldconfig"   Default all questions based on the contents of
                        your existing ./.config file and asking about
                        new config symbols.
177

M
Michael Witten 已提交
178 179 180 181
     "make silentoldconfig"
                        Like above, but avoids cluttering the screen
                        with questions already answered.
                        Additionally updates the dependencies.
182

K
Kees Cook 已提交
183 184 185 186
     "make olddefconfig"
                        Like above, but sets new symbols to their default
                        values without prompting.

M
Michael Witten 已提交
187 188 189 190
     "make defconfig"   Create a ./.config file by using the default
                        symbol values from either arch/$ARCH/defconfig
                        or arch/$ARCH/configs/${PLATFORM}_defconfig,
                        depending on the architecture.
191

M
Michael Witten 已提交
192 193 194 195 196 197
     "make ${PLATFORM}_defconfig"
                        Create a ./.config file by using the default
                        symbol values from
                        arch/$ARCH/configs/${PLATFORM}_defconfig.
                        Use "make help" to get a list of all available
                        platforms of your architecture.
198

M
Michael Witten 已提交
199 200 201
     "make allyesconfig"
                        Create a ./.config file by setting symbol
                        values to 'y' as much as possible.
202

M
Michael Witten 已提交
203 204 205
     "make allmodconfig"
                        Create a ./.config file by setting symbol
                        values to 'm' as much as possible.
206

M
Michael Witten 已提交
207 208
     "make allnoconfig" Create a ./.config file by setting symbol
                        values to 'n' as much as possible.
209

M
Michael Witten 已提交
210 211
     "make randconfig"  Create a ./.config file by setting symbol
                        values to random values.
212

213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230
     "make localmodconfig" Create a config based on current config and
                           loaded modules (lsmod). Disables any module
                           option that is not needed for the loaded modules.

                           To create a localmodconfig for another machine,
                           store the lsmod of that machine into a file
                           and pass it in as a LSMOD parameter.

                   target$ lsmod > /tmp/mylsmod
                   target$ scp /tmp/mylsmod host:/tmp

                   host$ make LSMOD=/tmp/mylsmod localmodconfig

                           The above also works when cross compiling.

     "make localyesconfig" Similar to localmodconfig, except it will convert
                           all module options to built in (=y) options.

R
Randy Dunlap 已提交
231
   You can find more information on using the Linux kernel config tools
L
Li Zefan 已提交
232
   in Documentation/kbuild/kconfig.txt.
R
Randy Dunlap 已提交
233

M
Michael Witten 已提交
234
 - NOTES on "make config":
235

M
Michael Witten 已提交
236 237 238
    - Having unnecessary drivers will make the kernel bigger, and can
      under some circumstances lead to problems: probing for a
      nonexistent controller card may confuse your other controllers
239

M
Michael Witten 已提交
240 241 242
    - Compiling the kernel with "Processor type" set higher than 386
      will result in a kernel that does NOT work on a 386.  The
      kernel will detect this on bootup, and give up.
243

M
Michael Witten 已提交
244 245 246 247 248
    - A kernel with math-emulation compiled in will still use the
      coprocessor if one is present: the math emulation will just
      never get used in that case.  The kernel will be slightly larger,
      but will work on different machines regardless of whether they
      have a math coprocessor or not.
249

M
Michael Witten 已提交
250 251 252 253 254 255
    - The "kernel hacking" configuration details usually result in a
      bigger or slower kernel (or both), and can even make the kernel
      less stable by configuring some routines to actively try to
      break bad code to find kernel problems (kmalloc()).  Thus you
      should probably answer 'n' to the questions for "development",
      "experimental", or "debugging" features.
L
Linus Torvalds 已提交
256 257 258

COMPILING the kernel:

A
Andrew Morton 已提交
259 260
 - Make sure you have at least gcc 3.2 available.
   For more information, refer to Documentation/Changes.
L
Linus Torvalds 已提交
261 262 263 264 265 266 267

   Please note that you can still run a.out user programs with this kernel.

 - Do a "make" to create a compressed kernel image. It is also
   possible to do "make install" if you have lilo installed to suit the
   kernel makefiles, but you may want to check your particular lilo setup first.

M
Michael Witten 已提交
268
   To do the actual install, you have to be root, but none of the normal
L
Linus Torvalds 已提交
269 270 271 272 273
   build should require that. Don't take the name of root in vain.

 - If you configured any of the parts of the kernel as `modules', you
   will also have to do "make modules_install".

R
Randy Dunlap 已提交
274 275
 - Verbose kernel compile/build output:

M
Michael Witten 已提交
276
   Normally, the kernel build system runs in a fairly quiet mode (but not
R
Randy Dunlap 已提交
277 278 279 280 281
   totally silent).  However, sometimes you or other kernel developers need
   to see compile, link, or other commands exactly as they are executed.
   For this, use "verbose" build mode.  This is done by inserting
   "V=1" in the "make" command.  E.g.:

M
Michael Witten 已提交
282
     make V=1 all
R
Randy Dunlap 已提交
283 284 285 286

   To have the build system also tell the reason for the rebuild of each
   target, use "V=2".  The default is "V=0".

L
Linus Torvalds 已提交
287 288 289 290 291 292 293
 - Keep a backup kernel handy in case something goes wrong.  This is 
   especially true for the development releases, since each new release
   contains new code which has not been debugged.  Make sure you keep a
   backup of the modules corresponding to that kernel, as well.  If you
   are installing a new kernel with the same version number as your
   working kernel, make a backup of your modules directory before you
   do a "make modules_install".
294

295 296 297
   Alternatively, before compiling, use the kernel config option
   "LOCALVERSION" to append a unique suffix to the regular kernel version.
   LOCALVERSION can be set in the "General Setup" menu.
L
Linus Torvalds 已提交
298 299 300 301 302 303 304 305

 - In order to boot your new kernel, you'll need to copy the kernel
   image (e.g. .../linux/arch/i386/boot/bzImage after compilation)
   to the place where your regular bootable kernel is found. 

 - Booting a kernel directly from a floppy without the assistance of a
   bootloader such as LILO, is no longer supported.

M
Michael Witten 已提交
306
   If you boot Linux from the hard drive, chances are you use LILO, which
L
Linus Torvalds 已提交
307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334
   uses the kernel image as specified in the file /etc/lilo.conf.  The
   kernel image file is usually /vmlinuz, /boot/vmlinuz, /bzImage or
   /boot/bzImage.  To use the new kernel, save a copy of the old image
   and copy the new image over the old one.  Then, you MUST RERUN LILO
   to update the loading map!! If you don't, you won't be able to boot
   the new kernel image.

   Reinstalling LILO is usually a matter of running /sbin/lilo. 
   You may wish to edit /etc/lilo.conf to specify an entry for your
   old kernel image (say, /vmlinux.old) in case the new one does not
   work.  See the LILO docs for more information. 

   After reinstalling LILO, you should be all set.  Shutdown the system,
   reboot, and enjoy!

   If you ever need to change the default root device, video mode,
   ramdisk size, etc.  in the kernel image, use the 'rdev' program (or
   alternatively the LILO boot options when appropriate).  No need to
   recompile the kernel to change these parameters. 

 - Reboot with the new kernel and enjoy. 

IF SOMETHING GOES WRONG:

 - If you have problems that seem to be due to kernel bugs, please check
   the file MAINTAINERS to see if there is a particular person associated
   with the part of the kernel that you are having trouble with. If there
   isn't anyone listed there, then the second best thing is to mail
L
Linus Torvalds 已提交
335 336
   them to me (torvalds@linux-foundation.org), and possibly to any other
   relevant mailing-list or to the newsgroup.
L
Linus Torvalds 已提交
337 338 339 340 341 342 343 344

 - In all bug-reports, *please* tell what kernel you are talking about,
   how to duplicate the problem, and what your setup is (use your common
   sense).  If the problem is new, tell me so, and if the problem is
   old, please try to tell me when you first noticed it.

 - If the bug results in a message like

M
Michael Witten 已提交
345 346 347 348 349 350 351 352
     unable to handle kernel paging request at address C0000010
     Oops: 0002
     EIP:   0010:XXXXXXXX
     eax: xxxxxxxx   ebx: xxxxxxxx   ecx: xxxxxxxx   edx: xxxxxxxx
     esi: xxxxxxxx   edi: xxxxxxxx   ebp: xxxxxxxx
     ds: xxxx  es: xxxx  fs: xxxx  gs: xxxx
     Pid: xx, process nr: xx
     xx xx xx xx xx xx xx xx xx xx
L
Linus Torvalds 已提交
353 354 355 356 357 358

   or similar kernel debugging information on your screen or in your
   system log, please duplicate it *exactly*.  The dump may look
   incomprehensible to you, but it does contain information that may
   help debugging the problem.  The text above the dump is also
   important: it tells something about why the kernel dumped code (in
M
Michael Witten 已提交
359
   the above example, it's due to a bad kernel pointer). More information
L
Linus Torvalds 已提交
360 361 362 363
   on making sense of the dump is in Documentation/oops-tracing.txt

 - If you compiled the kernel with CONFIG_KALLSYMS you can send the dump
   as is, otherwise you will have to use the "ksymoops" program to make
364 365 366
   sense of the dump (but compiling with CONFIG_KALLSYMS is usually preferred).
   This utility can be downloaded from
   ftp://ftp.<country>.kernel.org/pub/linux/utils/kernel/ksymoops/ .
367
   Alternatively, you can do the dump lookup by hand:
L
Linus Torvalds 已提交
368 369 370 371 372 373 374 375 376 377 378 379 380

 - In debugging dumps like the above, it helps enormously if you can
   look up what the EIP value means.  The hex value as such doesn't help
   me or anybody else very much: it will depend on your particular
   kernel setup.  What you should do is take the hex value from the EIP
   line (ignore the "0010:"), and look it up in the kernel namelist to
   see which kernel function contains the offending address.

   To find out the kernel function name, you'll need to find the system
   binary associated with the kernel that exhibited the symptom.  This is
   the file 'linux/vmlinux'.  To extract the namelist and match it against
   the EIP from the kernel crash, do:

M
Michael Witten 已提交
381
     nm vmlinux | sort | less
L
Linus Torvalds 已提交
382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397

   This will give you a list of kernel addresses sorted in ascending
   order, from which it is simple to find the function that contains the
   offending address.  Note that the address given by the kernel
   debugging messages will not necessarily match exactly with the
   function addresses (in fact, that is very unlikely), so you can't
   just 'grep' the list: the list will, however, give you the starting
   point of each kernel function, so by looking for the function that
   has a starting address lower than the one you are searching for but
   is followed by a function with a higher address you will find the one
   you want.  In fact, it may be a good idea to include a bit of
   "context" in your problem report, giving a few lines around the
   interesting one. 

   If you for some reason cannot do the above (you have a pre-compiled
   kernel image or similar), telling me as much about your setup as
398
   possible will help.  Please read the REPORTING-BUGS document for details.
L
Linus Torvalds 已提交
399

400
 - Alternatively, you can use gdb on a running kernel. (read-only; i.e. you
L
Linus Torvalds 已提交
401 402 403 404 405 406 407 408 409 410 411 412
   cannot change values or set break points.) To do this, first compile the
   kernel with -g; edit arch/i386/Makefile appropriately, then do a "make
   clean". You'll also need to enable CONFIG_PROC_FS (via "make config").

   After you've rebooted with the new kernel, do "gdb vmlinux /proc/kcore".
   You can now use all the usual gdb commands. The command to look up the
   point where your system crashed is "l *0xXXXXXXXX". (Replace the XXXes
   with the EIP value.)

   gdb'ing a non-running kernel currently fails because gdb (wrongly)
   disregards the starting offset for which the kernel is compiled.