提交 c59dc6cf 编写于 作者: J Jacopo Mondi 提交者: Greg Kroah-Hartman

media: ov5640: Re-work MIPI startup sequence

commit aa4bb8b8838ffcc776a79f49a4d7476b82405349 upstream.

Rework the MIPI interface startup sequence with the following changes:

- Remove MIPI bus initialization from the initial settings blob
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
  LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At s_stream time enable/disable the MIPI interface output.
- Restore default settings at set_power(0) time.

Before this commit the sensor MIPI interface was initialized with settings
that require a start/stop sequence at power-up time in order to force lanes
into LP11 state, as they were initialized in LP00 when in 'sleep mode',
which is assumed to be the sensor manual definition for the D-PHY defined
stop mode.

The stream start/stop was performed by enabling disabling clock gating,
and had the side effect to change the lanes sleep mode configuration when
stream was stopped.

Clock gating/ungating:
-       ret = ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
-                            on ? 0 : BIT(5));
-       if (ret)

Set lanes in LP11 when in 'sleep mode':
-       ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
-                              on ? 0x00 : 0x70);

This commit fixes an issue reported by Jagan Teki on i.MX6 platforms that
prevents the host interface from powering up correctly:
https://lkml.org/lkml/2018/6/1/38

It also improves MIPI capture operations stability on my testing platform
where MIPI capture often failed and returned all-purple frames.

Fixes: f22996db ("media: ov5640: add support of DVP parallel interface")

Tested-by: Steve Longerbeam <slongerbeam@gmail.com> (i.MX6q SabreSD, CSI-2)
Tested-by: Loic Poulain <loic.poulain@linaro.org> (Dragonboard-410c, CSI-2)
Reported-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NJacopo Mondi <jacopo@jmondi.org>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
上级 016a8fc5
......@@ -288,10 +288,10 @@ static const struct reg_value ov5640_init_setting_30fps_VGA[] = {
{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x3000, 0x00, 0, 0},
{0x3002, 0x1c, 0, 0}, {0x3004, 0xff, 0, 0}, {0x3006, 0xc3, 0, 0},
{0x300e, 0x45, 0, 0}, {0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
{0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
{0x501f, 0x00, 0, 0}, {0x4713, 0x03, 0, 0}, {0x4407, 0x04, 0, 0},
{0x440e, 0x00, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
{0x4837, 0x0a, 0, 0}, {0x4800, 0x04, 0, 0}, {0x3824, 0x02, 0, 0},
{0x4837, 0x0a, 0, 0}, {0x3824, 0x02, 0, 0},
{0x5000, 0xa7, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x5180, 0xff, 0, 0},
{0x5181, 0xf2, 0, 0}, {0x5182, 0x00, 0, 0}, {0x5183, 0x14, 0, 0},
{0x5184, 0x25, 0, 0}, {0x5185, 0x24, 0, 0}, {0x5186, 0x09, 0, 0},
......@@ -1104,12 +1104,25 @@ static int ov5640_set_stream_mipi(struct ov5640_dev *sensor, bool on)
{
int ret;
ret = ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
on ? 0 : BIT(5));
if (ret)
return ret;
ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
on ? 0x00 : 0x70);
/*
* Enable/disable the MIPI interface
*
* 0x300e = on ? 0x45 : 0x40
*
* FIXME: the sensor manual (version 2.03) reports
* [7:5] = 000 : 1 data lane mode
* [7:5] = 001 : 2 data lanes mode
* But this settings do not work, while the following ones
* have been validated for 2 data lanes mode.
*
* [7:5] = 010 : 2 data lanes mode
* [4] = 0 : Power up MIPI HS Tx
* [3] = 0 : Power up MIPI LS Rx
* [2] = 1/0 : MIPI interface enable/disable
* [1:0] = 01/00: FIXME: 'debug'
*/
ret = ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00,
on ? 0x45 : 0x40);
if (ret)
return ret;
......@@ -1790,23 +1803,69 @@ static int ov5640_set_power(struct ov5640_dev *sensor, bool on)
if (ret)
goto power_off;
/* We're done here for DVP bus, while CSI-2 needs setup. */
if (sensor->ep.bus_type != V4L2_MBUS_CSI2)
return 0;
/*
* Power up MIPI HS Tx and LS Rx; 2 data lanes mode
*
* 0x300e = 0x40
* [7:5] = 010 : 2 data lanes mode (see FIXME note in
* "ov5640_set_stream_mipi()")
* [4] = 0 : Power up MIPI HS Tx
* [3] = 0 : Power up MIPI LS Rx
* [2] = 0 : MIPI interface disabled
*/
ret = ov5640_write_reg(sensor,
OV5640_REG_IO_MIPI_CTRL00, 0x40);
if (ret)
goto power_off;
/*
* Gate clock and set LP11 in 'no packets mode' (idle)
*
* 0x4800 = 0x24
* [5] = 1 : Gate clock when 'no packets'
* [2] = 1 : MIPI bus in LP11 when 'no packets'
*/
ret = ov5640_write_reg(sensor,
OV5640_REG_MIPI_CTRL00, 0x24);
if (ret)
goto power_off;
/*
* Set data lanes and clock in LP11 when 'sleeping'
*
* 0x3019 = 0x70
* [6] = 1 : MIPI data lane 2 in LP11 when 'sleeping'
* [5] = 1 : MIPI data lane 1 in LP11 when 'sleeping'
* [4] = 1 : MIPI clock lane in LP11 when 'sleeping'
*/
ret = ov5640_write_reg(sensor,
OV5640_REG_PAD_OUTPUT00, 0x70);
if (ret)
goto power_off;
/* Give lanes some time to coax into LP11 state. */
usleep_range(500, 1000);
} else {
if (sensor->ep.bus_type == V4L2_MBUS_CSI2) {
/*
* start streaming briefly followed by stream off in
* order to coax the clock lane into LP-11 state.
*/
ret = ov5640_set_stream_mipi(sensor, true);
if (ret)
goto power_off;
usleep_range(1000, 2000);
ret = ov5640_set_stream_mipi(sensor, false);
if (ret)
goto power_off;
/* Reset MIPI bus settings to their default values. */
ov5640_write_reg(sensor,
OV5640_REG_IO_MIPI_CTRL00, 0x58);
ov5640_write_reg(sensor,
OV5640_REG_MIPI_CTRL00, 0x04);
ov5640_write_reg(sensor,
OV5640_REG_PAD_OUTPUT00, 0x00);
}
return 0;
ov5640_set_power_off(sensor);
}
return 0;
power_off:
ov5640_set_power_off(sensor);
return ret;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册